GRP WATER TANK

Capacity U.S Gallon Length C.M. Width C.M. Height C.M. No. of. Legs
250 135 112 112 2
300 154 110 110 2
400 180 130 120 2
500 195 130 142 2
600 203 135 145 2
800 207 150 165 2
1000 227 160 175 2
1200 245 170 190 2
1500 287 180 180 3
2000 285 225 235 2
2500 315 225 235 2
3000 385 225 235 2
4000 485 225 235 4
5000 590 225 235 5
6000 572 250 250 6
10000 735 285 280 6
15000 1050 285 280 9

INTRODUCTION

Our G.R.P. Tanks are manufactured with the experienced hands and will meet all our tanks requirements. We make tanks for different purposes like the storage of Drinking water, sewage water, oil chemical etc.

SHAPE

Attractive Cylindrical Horizontal shape, specially designed to suit the capacity and long life.

LAMINATION METHOD

Hand Lay-up

SURFACE

Smooth and shining Isophthalic white Gelcoat finishing for inner surface and waxed gel coat coating for external surface in white colour.

ANTIFUNGUS LAYER

A middle layer is provided with advised chemical to prevent fungus and Ultra violet Rays.

JOINTS

All the joints are done by G.I Nut Bolts covered with GRP Gel coat

STRUCTURE

1 mm. Thick white gel coat Interior Layer finishing. A surface Mat is provided to protect inner coating. Adequate layers of fibre mat and woven roving layers will be applied according to the capacity of the tank using required Resin and chemicals to suit the usage of tank. The middle layer will be for Anti Fungus Treatment. The over coat will be given with waxed white coating to get a clear look.

EXTRA FITTINGS

Inlet, Outlet , Drain and over flow connection with PVC Heavy Duty pipe will be provided free of cost on request. Note : If you connecting outlet with heavy valves and fittings the overweight will be effected to the Tank . So you should be take precautions for this overweight not to be effecting to the tank. Keep suitable support and make sure the connections are not hanged

PHYSICAL CONTENTS
  • Resin – 75%t
  • Fibre – 25%
  • Thickness : 6 to 8 mm
ERECTION

The Tanks should be seated in a Flat smooth Concrete surface and in proper level so that only the total load will be equally distributed on each leg.

GRP SEPTIC TANK

Capacity U.S Gallon Length C.M. Width C.M. Height C.M. No. of. Legs
250 135 112 112 2
300 154 110 110 2
400 180 130 120 2
500 195 130 142 2
600 203 135 145 2
800 207 150 165 2
1000 227 160 175 2
1200 245 170 190 2
1500 287 180 180 3
2000 285 225 235 2
2500 315 225 235 2
3000 385 225 235 2
4000 485 225 235 4
5000 590 225 235 5
6000 572 250 250 6
10000 735 285 280 6
15000 1050 285 280 9

INTRODUCTION

Our G.R.P. Tanks are manufactured with the experienced hands and will meet all our tanks requirements. We make tanks for different purposes like the storage of Drinking water, sewage water, oil chemical etc.

SHAPE

Attractive Cylindrical Horizontal shape, specially designed to suit the capacity and long life.

SURFACE

Smooth and shining isophthalic white Gelcoat finishing for inner surface and waxed gel coat coating for external surface in white colour.

JOINTS

All the joints are done by G.I Nut Bolts covered with Gelcoat coating.

STRUCTURE

1 mm. Thick gel coat ( Isophthalic ) Interior layer finishing. A surface Mat is provided to protect inner coating layer with Iso Resin . One Layer 300 GSM fibre mat will be laminated with Iso Resin . Adequate layers of fibre mat and woven roving layers will be applied according to the capacity of the tank using required Resin and chemicals to suit the usage of tank. The middle layer will be for Anti Fungus Treatment. The over coat will be given with waxed coating to get a clear look.

PARTITION

Two / Three separate compartments interconnected with 4 inch or 6 inch openings on the middle will be made using G.R.P. sheets with reinforced ribs.

EXTRA FITTINGS

Inlet and Outlet will be provided free of cost on request.

THICKNESS

It depend upon the capacity of the tank.

ERECTION

Proper excavation should be done if you keep the septic tank below the ground level. The base should be properly concreted in level to get equal seating of the legs of the tank. Side walls and top should be provided to protect the Septic Tank from the external pressure.